|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IntelliCAD - Download |
|
IntelliCAD is AutoCAD compatible thus many of the blocks and lips routines found here have been created for AutoCAD but will equally work on IntelliCAD. So don't forget to visit my AutoCAD Zone |
Blocks |
|
Miscellaneous North Arrows and Scale Bars.(73KB file) |
|
Domestic and Commercial Vehicles on Plan, Side Front and Rear (404KB) |
|
Doors on Elevation (138KB File) |
|
Trees on Elevation & Plan, Trees are drawn at 1m high or diameter, allowing you to scale when you place. (783KB File) |
|
Men on plan and elevation various poses (1.143 Mbyte File) |
|
Women on elevation, (376KB File) |
|
Groups of people (92KB File) |
|
Family Groups, Mum with children, Peggy Phil and Grant. (96 KB File) |
|
Couples (259KB File) |
|
Children sitting, playing ball. (127KB File ) |
|
Tennis, Bike Riding, Horse Jumping, Skateboarding (224KB File |
|
|
|
|
|
|
|
Lisp Routines |
Command Line Routines |
Lisp routine that provides Generic Cadd Commands within AutoCAD. Author Alan James Wooldridge
|
|
Lisp routine that provides the snap from function missing from IntelliCAD. This is a must have LISP, I have requested that the ITC add this function into version 5 of IntelliCAD
|
Lisp Routines |
Drawing Routines |
|
Or
|
The purpose of this routine is to allow the user to pick points and have the coordinates written as entities to the drawing at each point as picked. To Run:- At the command line, type (load "c:/lispdir/crdbypck") where c:/ is the drive where CRDBYPCK.lsp is contained lispdir/ is the directory or folder where CRDBYPCK.lsp is contained
|
This routine will produce a cut tube symbol on parallel lines, prompting the user to select two lines. Other options are prompted.
|
|
This routine draws thermal insulation; the user specifies the start and end of the insulation then the thickness.
|
|
FREEHAND.lsp (c) Copyright 2000 TimeSavers for CAD from http://www.timesaversforcad.com
This lisp routine modifies lines and polylines to appear as if drawn freehand. Two things occur:
1. Corners are given slight overlap. 2. Lines are given slight "wiggle" to them.
User can specify degree of both overlap & wiggle [1 small - 5 large, 0-none] Accomplished by first lengthening each line, then replacing line with LWPOLYLINE(R14) or POLYLINE(<R14) and adding slightly offset vertices.
Ensure that you only FREEHAND a Copy of your elevation, once run there is no way back ! Keep your original drawing safe.
|
Lisp Routines |
Editing Routines |
This routine can be called by typing one of three commands at the command prompt.
All three commands will ask the user to select to corners of a rectangle. This Lisp routine was loaded of the web and modified to add the Cadvance macro name. It should be noted that this AutoCAD lisp is not as clean as the Cadvance versions.
The first command, SCB or BIGTRIMB, will erase and trim all entities outside of the rectangle and leave a polyline border.
The second command, SC or BIGTRIM, will erase and trim all entities outside of the rectangle but will not leave a border.
The final command, SCD or RECTRIM, will erase and trim all entities inside of the rectangle and will not leave a border.
|
|
xyz scaling of selected entities. This routine gives that same functionality as the CADVANCE scale command.
|
|
|
|
Lisp Routines |
Block Routines |
This little routine will let you designate a target path and automatically wblock all the blocks in your drawing.
|
|
|
|
Lisp Routines |
Layer Routines |
This AutoLISP routine will export a drawing's layer table to .CSV (Comma Separated Values) format that can be opened up directly within Microsoft Excel (or any text editor if you don't have Excel). The layer name, colour, linetype, and frozen / thawed status are exported as well as column headings and the full drawing file name
|
|
|
|
Menu Files |
AutoCAD mnu files |
AutoCAD R14
AutoCAD LT2000
AutoCAD LT 2000I
AutoCAD LT 2002
AutoCAD LT2004 |
Following a discussion on the Cadopia forum regarding customising IntelliCAD where a user wanted to get hold of an AutoCAD(R) menu. It was found that the menu *.mnu files may be distributed so those that I have access to are here. If you have any missing versions please send me a copy and I will add them here for all to have access too.
The Legal bit now follows:-
Permission to use, copy, modify, and distribute this software for any purpose and without fee is hereby granted, provided that the above copyright notice appears in all copies and that both the copyright notice and the limited warranty and restricted rights notice below appear in all supporting documentation. AUTODESK, INC. PROVIDES THIS PROGRAM "AS IS" AND WITH ALL FAULTS. AUTODESK, INC. SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. AUTODESK, INC. DOES NOT WARRANT THAT THE OPERATION OF THE PROGRAM WILL BE UNINTERRUPTED OR ERROR FREE. Use, duplication, or disclosure by the U.S. Government is subject to restrictions set forth in FAR 52.227-19 (Commercial Computer Software - Restricted Rights) and DFAR 252.227-7013(c)(1)(ii) (Rights in Technical Data and Computer Software), as applicable.
|
|
|
DISCLAIMER:( AKA the small print) CADALOT DISCLAIMS ANY AND ALL LIABILITY FOR ANY DAMAGES ARISING OUT OF THE USE OR OPERATION, OR INABILITY TO USE ANY SOFTWARE OR FILES AVAILABLE HERE. FURTHERMORE, BY DOWNLOADING ANY FILE YOU AGREE TO HOLD CADALOT HARMLESS FROM SUCH CLAIMS. CADALOT makes no warranty, either expressed or implied, as to the fitness of these files for any particular purpose. All materials are to be considered "as-is", and use of any files should be considered as AT YOUR OWN RISK ) |
|
All Site Logos and images are © by the rightful owners, and I thank them all for allowing me to use them here. |
|
Last Update 14th September 2007 |
(c) cadalot.co.uk 2000 - 2007 |
